1. カメラ
  2. カーオーディオ&エレクトロニクス
  3. ホームオーディオ
  4. パーソナルオーディオ
  5. テレビ
  6. スマートホーム
  >> 電子技術オンライン >  >> ホームオーディオ >> スピーカー&サブウーファー

サブウーファーの位相がずれているかどうかを確認する方法

多くの人は、サブウーファーをどのフェーズに設定するか、サブウーファーが同相か異相かを判断する方法を決定しようとするときに混乱します。

この記事では、オーディオ フェーズの考え方を単純化し、サブウーファーの位相がずれているかどうかを確認する方法を説明します。

サブウーファー フェーズとは

簡単に言えば、オーディオ位相とは、オーディオ波形またはオーディオ信号のタイミングを指します。音声信号は、山と谷で構成される正弦波と呼ばれるものとして伝わります。

サブウーファーが同相の場合

2 つの波のタイミングがまったく同じ場合、それらの山と谷は一致し、波は同相であると言われます。

波は同相で山と谷が一致するため、 の信号は加算されます。これが建設的干渉と呼ばれるもので、全体的な信号がより強くなります。

下の図をご覧ください。

ホーム シアター システムのサブウーファーとメイン スピーカーに関する限り、これは物理的にサブウーファーのコーンがスピーカーは、サブウーファーのクロスオーバー周波数で同期して前後に移動します。

クロスオーバー周波数は、サブウーファー周波数がカットアウトし、スピーカー周波数がカットインするポイントです。つまり、サブウーファー周波数が最高で、メインスピーカー周波数が最低です。

最終的に、それらは互いのアウトプットを強化します。サブウーファーのクロスオーバー周波数の設定について詳しくは、次のリンクをご覧ください。

Surboower がアウトまたはフェーズになった場合

一方、2 つの信号のタイミングが正確に一致していない場合、2 つの信号が結合すると、信号のピークと谷が正確に一致しないため、破壊的な干渉が発生します。

信号の位相がずれているほど、破壊的な干渉が発生します。信号の位相が完全にずれている場合、完全に破壊的な干渉または信号のキャンセルが発生します。

物理的には、これはメイン スピーカーのコーンが後方に移動し、サブウーファーのコーンが前方に移動することを意味します。それらは同期して動きません。

この場合、それらは互いの出力を低下またはキャンセルします。

これは、結果として得られる信号が弱くなり、明確ではないことを意味します.

このため、ホーム シアター システムのサブウーファーに正しい位相を設定して、サブがシステムの残りの部分 (メイン スピーカー、センター スピーカーなど) と同相であることを確認することが非常に重要です。

フェーズは、サウンド システムにおいて重要です。この設定は、曲の要素、サウンド エフェクト、またはその他のオーディオに聴覚的な影響を与える可能性があるためです。

この事実にもかかわらず、ほとんどの場合、オーディオの位相ずれの問題は非常に微妙にしか現れず、通常は検出が非常に困難です。

システムが同相である場合、オーディオはより強く鮮明になります。

サブウーファーの位相制御とは?

位相とは何かがわかったので、サブウーファーの位相制御とは何ですか?

簡単に言えば、サブウーファーの位相制御により、入力信号に電気的なタイミング遅延を追加できます。一般に、位相制御は 0 ~ 180 度の範囲で動作します。一部のサブウーファーには、0 度または 180 度の位相を可能にする位相スイッチがあります。

ほとんどのサブウーファーには、この連続可変 0 ~ 180 位相制御ノブがあり、可能な限り最高のサウンドを実現するために、小さな位相増分で最も完全な範囲の調整が可能です。

ホーム テッター システムのスピーカーの位相に応じて、サブウーファー信号に正しい遅延を追加すると、ラウドスピーカーをより適切に統合するのに役立ちます。

では、0 ~ 180 度の設定は何を意味するのでしょうか?

このように考えてみてください。この値は、波のタイミングを決定する波のシフトの度合いを決定します。この数値が高いほど、波がシフトするか、波が遅れます。

サブウーファーの位相がずれているかどうかを確認する方法

フェーズ スイッチの使用は、適切なフェーズを設定し、サブ スピーカーとメイン スピーカーが同相であることを確認するという点で、サブ スピーカーを残りのスピーカーと統合するのに役立ちます。

ただし、サブウーファーの位相の設定に関連する厳格な規則はないことを理解することが重要です。

これは、最適なサブウーファーの位相を見つけることが、サブウーファーと部屋の音響に対する他のスピーカーの配置に大きく依存するためです。

ただし、サブウーファーの位相を設定するために使用できる段階的な手順があります。

では、サブウーファーの位相がずれているかどうかはどうやってわかりますか?

<強い>1.薄い低音を聞く: まず、フェーズ キャンセレーションは、特にクロスオーバー周波数以下の低周波音で最も顕著です。

これは、位相のずれの影響が低周波数で強くなるため、低音が失われ、ステレオ イメージングが歪む可能性さえあるからです。

位相の問題を検出しようとするときは、注意深く耳を傾ける必要があります。サブウーファーの位相がずれている場合、可聴結果は通常、低音がほとんどまたはまったくない薄い音の信号になります。

検出が難しいもう 1 つの一般的な問題は、低音が 1 つの場所から発生するのではなく、ミックス内を移動することです。

学習するように、位相は聞くだけで判断するのは困難です。注意深く耳を傾け、低音域と高音域で音楽がどのように聞こえるかをある程度理解する必要があります。

このプロセスを簡単にするには、システムをより高い周波数範囲に設定し、位相の問題を聞きます。

これができるのは、クロスオーバーがより緩やかで周波数範囲が高いほど、位相の変化が聞き取りやすいからです。

<強い>2.変更して聞く: もう 1 つの簡単な方法は、メインのリスニング ポジションから聞いている間に、誰かにサブの位相を変えてもらうことです。最適な位相設定は、低音が最も強烈なポイントになります。

<強い>3. SPL または dB メーターを使用する: この方法は、音の周波数にあまり慣れていない人向けです。 You can use an SPL meter (Sound Pressure Level meter) to see how it affects the sub’s output with pink noise.

It is usually recommended to use the setting that yields the highest pink noise output when the sub’s + main channels are playing at the same time. You don’t even need to purchase an expensive meter to do this. There are many SPL or dB meter apps out there.

Subwoofer Phase and Frequency

While you will be able to detect phase issues easier at higher frequency ranges, it is important to realize that setting phase is always dependent on frequency.

As such, subwoofers and speakers are said to be in or out of phase at a particular frequency.

In other words, the phase of both devices changes with frequency. This means that if you get your speakers and sub in phase at 80 Hz, they might not be at 100 Hz.

So, even if you get your system in phase at 100 Hz, you still need to recalibrate and get it in phase at 80Hz if that is your normal operating frequency.

Normal and Reverse Subwoofer Phase

While many subwoofers have a 0 to 180 phase dial, other subwoofers may have a simple 0/180 phase switch which allows you to change the polarity of the subwoofer.

Setting the phase to 0 is known as the normal phase while setting the phase control to 180 degrees reverses the polarity of the subwoofer. Here’s a quick overview:

  • Normal: keeps the polarity (+/-) of the Sub the same relative to the rest of your speakers.
  • Reverse: flips the polarity (-/+) of the Sub relative to the rest of your speakers. This means that the sub will be 180 degrees out of phase.

When you reverse the polarity of a subwoofer, the subwoofer’s driver moves inward while all other speaker drivers in the system are moving outward.

Of course, this is not as useful as a true variable phase control. However, it is actually useful in some applications.

Take for example, if the subwoofer is placed on a wall opposite from the speakers, reversing the subwoofer polarity can improve the sub’s response.

How Do I Get The Most Out Of My Subwoofer Phase And Positioning?

A great way to get optimal function from your subwoofer is to crank the volume of your subwoofer to its maximum setting, then toggle the sound levels till you find your preferred settings.

Why Would A Subwoofer Be Out Of Phase?

Subwoofers operate on a push and pull principle directly controlled by the polarity of signals they receive. When a positive signal goes to the speaker, it pushes the woofer forward. When the signal sent is negative, the woofer pulls itself backward. Too much negative/inverted signals will put the woofer out of phase

Should The Subwoofer Phase Be Normal Or Reverse?

This is dependent on how many subwoofers you are using. If you’re working with one single subwoofer, your phase settings should be set to Normal.
The phase should be set to Normal if you are running just one subwoofer. When dealing with two subwoofers, one should be set to normal and the other one set to reverse.

Why Are My Subwoofers Pulsing?

This is usually a problem between the amplifier and your woofer. You have to make sure your speaker wires aren’t shorting, especially at their point of connection.

What Is Polarity On A Subwoofer?

Polarity is a term used to show whether a signal is positive or negative. Inverting polarity means that what was positive is now negative and vice versa.
This implies that, reversing the connection of your speaker wires will reverse its polarity.

結論

There are many ways to determine if your subwoofer is out of phase. One way is to listen for thin bass just below the crossover frequency, another way is to vary the phase and listen at the main listening position in the room or us an SPL meter and check out the subs pink noise output is affected.

In general, you will get the best bass out of your subwoofer by varying settings such as amp gain and crossover frequency. However, you need to consider your subwoofer placement in the room as well as overall room acoustics to get the best bass. All the best!