1. カメラ
  2. カーオーディオ&エレクトロニクス
  3. ホームオーディオ
  4. パーソナルオーディオ
  5. テレビ
  6. スマートホーム
  >> 電子技術オンライン >  >> スマートホーム >> 家電

洗濯機が動かないのはなぜですか?

洗濯機が動かなくなるまで、洗濯機の重要性に気づきません。考えてみてください。この控えめなユニットのおかげで、学校の制服の洗濯から作業着の洗濯まで、家事をすべて手作業で行う必要がなくなります。コイン ランドリーで時間を無駄にしないでください。洗濯機が天候下にある場合に考えられる問題と解決策に関するガイドをお読みください。

洗濯機の電源が入らないのはなぜですか?

そもそも洗濯機がオンにならない理由にはいくつかの要因があります:

  • 壁のコンセントに接続されておらず、電力が供給されていない可能性があります。ランプなどの別の電化製品を接続して壁のソケット自体をチェックし、電源が切れていないことを確認できます。それ以外の場合は、サーキット ブレーカーを確認する必要があります。
  • また、ユニットの電源コードをチェックして、コードの交換が必要なほつれや破損がないかどうかを確認することもできます。
  • 一部の洗濯機には、電源を入れる前に洗濯機のふたを完全に閉じる必要がある安全システムも備わっています。
  • 洗濯機にもふたのスイッチが付いていますが、壊れている可能性があります。テストするには、ふたを開けてスイッチを見つけ、押して放します。カチッと音がしない場合は、交換が必要な場合があります。

サイクルの途中で洗濯機が動かなくなったのはなぜですか?

洗濯機がサイクルの途中で停止した場合、モーターをロックする過負荷保護システムが搭載されている可能性があります。洗濯物の負荷が大きいと、モーターに負担がかかる場合があります。この場合、ユニットはエラー コードを表示して、この問題を通知する場合があります。通常、システムが自動的にリセットしてマシンを再起動できるように、負荷の一部を取り除く必要があります。場合によっては、ユニットをリセットするために、再接続する前にマシンのプラグを完全に抜く必要があるかもしれません.

洗濯機のリセット方法

洗濯機をリセットする方法は、所有しているブランドと特定のモデルによって異なります。次の手順が異なる場合があるため、マニュアルまたはブランドの Web サイトを参照する必要がある場合があります。

<オール>
  • 「電源」ボタンを押して洗濯機をオフにします
  • コンセントから洗濯機のプラグを抜きます
  • ユニットの回路ブレーカーをオフにする
  • 電源が​​オフになっているときに、開始/一時停止ボタンを 5 秒間押し続けます
  • ワッシャーを再び差し込む
  • サーキット ブレーカーをオンにする
  • エラーが引き続き表示される場合は、修理サービスが必要な場合があります。

    洗濯機が衣類に残留物を残すのはなぜですか?

    洗濯機が適切にすすがれていない場合、サイクル後に衣類に洗剤の残留物が見つかることがあります.いくつかの理由が考えられます:

    • 洗剤: 洗濯機をどのように使用しているかを評価することが重要です。洗剤は適量入れていますか?負荷に対して十分な水を使用していますか?洗剤が多すぎたり、水が足りなかったりすると、洗剤自体が残留物を残している可能性があります。
    • 汚れたドラム: 時間の経過とともにドラムに油分がたまり、クリーニングが必要になる場合があります。これには浴槽の掃除サイクルを使用できます (利用可能な場合)。それ以外の場合は、浴槽を手で拭きます。
    • オーバーロード: ユニットに過負荷をかけると、衣服を完全に洗うのに苦労し、残留物が残る可能性があります.取扱説明書には、洗濯機に安全に入れることができる重量を指定する必要があります (オンライン コピーは通常、ブランドの Web サイトから入手できます)。 1kgの洗濯物はこんな感じです:

    洗濯機がすべての水を排出しないのはなぜですか?

    サイクル後に洗濯機がすべての水を排出しない場合、または正しく排出されない場合は、次の手順に従ってください:

    <オール>
  • 供給ホースを点検します: そのためには、ユニットのスイッチを切り、給水を止めてください。ユニットからホースを外し、端をシンクまたはバケツに入れ、蛇口を元に戻します。強いフローがあることを確認してください。そうでない場合、部分的にブロックされている可能性があります。完全に開いていて、どこにもねじれていないことを確認してください。詰まりを取り除くか、必要に応じてホースを交換してください。
  • 排水ホースを点検します: 排水ホースもチェックして、すべての水が排出されていることを確認します。詰まりがあると、水が逆流してドラム内に留まる可能性があります。必要に応じて障害物を取り除きます。
  • 洗濯機が水漏れするのはなぜですか?

    洗濯機の水漏れは、ホースまたは接続の緩みが原因である可能性があります:

    <オール>
  • 水を止める
  • ホースを取り外し、バケツに排水します
  • フィッティングを確認してください: ホースがユニットに接続されているフィッティングと、タップに接続されているフィッティングを確認してください。必要に応じてホース フィッティングを締めるか、交換します
  • シールを確認してください: ドアのシールを確認し、蓄積している可能性のある石鹸の残留物を取り除きます。必要に応じてシールを交換してください
  • ホースの詰まりや磨耗がないか確認してください: 水漏れがバックアップされたホースによって引き起こされていないことを確認してください。磨耗したホースは交換が必要な場合があります
  • 泡立ちをチェック: 洗剤の量が多すぎたり、間違った種類の洗剤を使用したりすると、泡があふれることがあります。これを解消するためにオンラインで見つけることができるさまざまな自家製の救済策があります。たとえば、大さじ 2 杯の重炭酸ソーダを洗剤の引き出しに入れ、コップ半分の白酢をドラム缶に入れ、通常の洗濯を行います
  • 洗濯機が揺れるのはなぜですか?

    洗濯機が異常に揺れている場合は、次のようなさまざまな理由が考えられます:

    • 洗浄量のバランスが悪い: 衣類が浴槽の片側に束ねられていないか確認し、必要に応じて負荷を調整してください。
    • マシンが水平になっていません: 平準化されたサポートについてマシンを確認してください。洗濯機が置かれている床が平らで、洗濯機がいっぱいになった洗濯機を支えるのに十分な強度があることを確認してください。

    以下の具体的な手順に従って、洗濯機を水平にしてください。

    洗濯機を水平にする方法

    <オール>
  • 洗濯機の電源がオフで、プラグが抜かれていることを確認する
  • 足の高さをチェック: 洗濯機の下を見て、すべての足が床に正しく置かれていることを確認します。必要に応じて足を締めます。 Place a level on top of the machine to check and adjust the feet if needed
  • Check the rubber caps: the front legs of a washing machine generally have rubber caps. Make sure they are fitted on tightly and replace them if needed
  • Check back feet: this can be done by tilting the washing machine forward if necessary
  • Replug the unit and turn it back on
  • Run a cycle to check for vibration
  • Why is my washing machine making noises?

    If your washer is making a loud noise during a spin cycle, it could be caused by:

    • Faulty belt
    • Clutch assembly has worn out
    • Failing drive motor

    Typically, the above instances require a manufacturer’s assistance. It might also be an item that you’ve forgotten to take out of your pockets such as loose change, which will require you to stop the cycle and remove.

    Why isn’t my washing machine spinning?

    There are several reasons why the machine might not spin or agitate. It could be from:

    • Faulty lid switch: if the switch is broken, the unit might halt during a cycle. Replace the switch if needed.
    • Broken belt: tighten the belt if it has become loose otherwise it might be broken and needs to be replaced.
    • Defective buttons: it’s possible that the controls are not working, which might require a repair.
    • Load jammed: if any garments have jammed, making the drum unbalanced, you may need to readjust the load.

    Other situations such as a faulty motor, may require a repair service.

    Regular maintenance

    Before spending money on a service, it’s important to consider how long you’ve had the washer for. In Canstar Blue’s customer surveys, we’ve asked thousands of Australian households about how long they owned their appliances before replacing them. Based on these findings, the average life expectancy of front loaders was found to be 8 years and for top loaders it is 9 years. To help prolong the life of your washing machine, ensure that you conduct regular maintenance, as well as use the correct amount of detergent, and don’t overload it.

    Tub clean cycle

    It’s recommended to run a tub clean cycle (if available) about once a month or every 30 washes. You might need to run it more often if there’s a smell coming from the tub.

    <オール>
  • Empty the drum
  • Add washing machine cleaner (tablets are recommended to be placed directly in the drum while powder or liquid can be placed in the dispenser)
  • Start the tub clean cycle
  • Wait for the washer to cool down
  • Wipe the washer lid and glass door with a towel or soft cloth
  • Leave the washer lid open to ventilate
  • The tub clean cycle might help your washer maintain its optimal performance and it does the job for you with one press of a button.

    Clean filters

    Washing machines are generally fitted with a water inlet filter, which can get clogged especially if you live in an area with hard water. Newer models are designed to detect if the water is not entering the dispenser properly and show an error sign. To clean the filter:

    <オール>
  • Turn the water taps off
  • Turn off the washing machine and unplug it
  • Unscrew the hot and cold water lines from the back of the washing machine
  • Drain out the hoses into a bucket
  • Remove the inlet filter by using pliers or any other tool with small tips
  • Soak the filter in lime scale remover or white vinegar
  • Wash filters thoroughly in warm water to remove all build-up
  • Rinse filters before reinstalling and re-attaching the water lines

  • The wash-up

    As not every problem can be fixed, you may need to call a washing machine repairer. However, if your washer is drawing to the end of its life, consider purchasing a new one with a high energy-efficiency rating. Washers are constantly being upgraded, so there might be a lot of additional functionality that might be of benefit to you. Units with Wi-Fi connectivity from brands such as Samsung and LG allow you to troubleshoot problems via an app. To see which brands are keeping Aussies happy, follow the link below to our online ratings.

    Picture credits:New Africa/shutterstock.com, Andrey_Popov/shutterstock.com, tete_escape/shutterstock.com, Bacho/shutterstock.com, Africa Studio/shutterstock.com, Elena Loginova/shutterstock.com, Evgeny Atamanenko/shutterstock.com